loading
reading
writing
saving
searching
1972 C10 - $35 - $35,000 (dublin / pleasanton / livermore)
1972
C10
QR Code Link to This Post
I have had this truck about 10 years now and probably driven it no more that 100 miles. I have a disabled daughter and just do not have time to work on it and finish it. The truck is in good running condition as is and has a clean title. I do not have any history on the engine, but it does run good with no leaks and doesn’t smoke. Could use an alignment
The frame was originally a long bed but converted to short bed by previous owner. It appears that the actual bed is an original short bed. It has been sitting in a dry storage for nearly the entire time I have owned it. There is no visible rust except for a 1/8-1/4" bubble on the door. That was there when I got it and it has not gotten any larger and may not be rust at all, rather than a defect when it was painted. I have already done some upgrades such as lowering spindles/brackets, new STEEL grill, not aluminum, new Classic Instruments gauges, new chrome master cylinder, new ceramic coated long tube headers, new carburetor, new distributor and wires, new steering wheel (sure I am missing something else).
There are some issues that I know of: The doors do not close properly so they need some adjustment. While the paint overall is fairly decent, there is a scrape on the drivers side of the truck from when it was in storage (what a story that was). The bed has spray on bed liner, there is a section about 4"x4”; that was cut at 90 degree angle and peeling up… and I couldnt get the bed latch to work. There is no heater or air components, although I do have brand new control unit already in.
I have tons of new parts, over 10K, 90% still new in boxes, all new CPP suspension including all (3) cross members and motor mounts, 5x7 drop (see picture of the CPP Truck stance for reference), sway bar, control arms (all tubular), rebuilt rear end (think 3.73 gears), Champion 4 row radiator, CPP under bed aluminum gas tank, inner fender wells, new Energy Suspension body mounts (see below for list... sure I am missing stuff though)
I have a SWB frame that I was planning on building with all the new parts as a rolling chassis and then swap over the cab and bed, plan was to get it powder coated but just have not had the time to get to that. Also included is a set of US mags with good BFGoodrich Radial TA’s
The only other thing I was going to get was a front disc brake setup to have a complete rolling chassis (or can pull from the truck itself) and a new wire harness.
I am by no means in any rush to sell this. I am asking a firm 35K with everything I have to include.
Cash in hand for any test rides
May consider trades of equal value, no rust, must be in good running condition.... 66-72 Chevelle, 69-72 Camaro, 70-72 GTO, 77-81 Trans AM.... or newer Challenger/Charger R/T, Scat Pack or above with low miles, 2020 and up Silverado/Sierra Crew Cab with low miles, must have clean title.... let me know what you got
Below is a pretty accurate list of the items since I got the truck, most of which are not installed and still in original boxes
Vent/Heater Control
Cigarette Lighter
Window Air Vents
Grille Insert
Steel Grille
Grille Bowtie Emblem
McGaughey’s Drop Spindles 2.5 Drop
Belltech Street Performance Front Shocks
Belltech Street Performance Rear Shocks
2208AA fits with 2”-5” rear lowering
Upper and Lower Ball Joints
Rebuilt RearEnd with 3.73 Gears by
Transmission and Motor Works - Stockton, CA
Pedal Covers
Door Handles
Battery
Battery Cutoff Switch
Summit Racing SUM-G9006-9 - Ceramic Coated Headers
Steering Wheel
Seat Belts
Tailgate Latch
Fuel Cap
Wiper/Light Knobs
Window Vent Hardware/Weatherstripping
Door Jam Vent
Sun Visor Bracket and Hooks
Parking Brake Handle
Console Cup holder
AMD Radiator Core Support
CPP Upper Tubular Control Arms
CPP Lower Tubular Control Arms
CPP Front Sway Bar
CPP POWER STEERING GEAR BOX 500 SERIES
CPP 18 Gal Under Bed Aluminum Fuel Tank
Classic Instrument "Velocity" Gauges
Champion 4 Row Aluminum Radiator, 2 Electric Fans and Fan Relay Kit
Chrome Master Cylinder
New Window Vent Assembles
New rear tinted window
Billet interior door handles/window cranks
Rear View Side Mirrors
New Hood Hinges w/Springs
Stainless Steel 56oz Overflow Tank
Radiator Support to Grill Filler Panel Black
Hood Latch assembly and support
Inner Fenders
14x4 Black High Flow Air Cleaner
Good mark Antenna
Bed Mat
Kick Panels with 6.5 Speakers
Spark Plug Wires, Spiro-Pro, 8mm, Purple
Spark Plug Wire Loom - Polished
Transmission Pan, Aluminum, Polished, Finned
LMC Armrests
Billet Shifter/Turn Signal Levers
Billet Window Cranks
14" Black Aluminum Red Bowtie Steering Wheel
CPP Front End Rebuild Kit
CPP Trailing Arm Crossmember
CPP Transmission Crossmember and Engine Mounts
CPP Rear Shock Crossmember
CPP Front Suspension parts (Springs, Shocks)
Centerlink - Vintage Chevy
CPP Tubular Trailing Arms/Springs/shocks/
shock relocation kit/Sway bar/Deluxe trac bar/C-Notch Kit/lowering block and all hardware
Radiator Support Bracket (frame mount - Pair)
Radiator Support Mount Kit
Energy Suspension Body Mount Bushings
Edelbrock Performer Carburetors 1405 E/Choke